- +49 (0)9461/401596
- info@heide-flaechenfertiger.com
- Mo-Sa 8.00-18.00
-
-
Click on the markers to learn more about the individual components.
Click on the markers to learn more about the individual components.
Total length:
Total width:
Total height:
3.730 mm
2.200 mm
2.700 mm
Empty weight:
Total weight:
Payload:
approx. 1.480 kg
approx. 4.500 kg
approx. 3.020 kg
Engine manufacturer:
Fuel type:
Max. power at rpm:
Number of cylinders:
Cooling:
Tank capacity:
Kohler/Perkins
Diesel
18.4 kW
3
water-cooled
25 l
Drive type:
Track system:
Max. speed 1st gear:
Max. speed 2nd gear:
hydrostatic drive
low-vibration, low-wear
0 - 2 km/h
2 - 4 km/h
The HEIDE PRM-275 Surface Paving Machine is delivered ready to drive, with a foldable driver protection roof, without measuring devices (laser/ultrasound/cross slope) for height detection, without freight and transfer, and without training in the basic configuration.
All information is provided without guarantee. Deviations of up to 5% are possible depending on the equipment.
The HEIDE PRM-275 Surface Paving Machine meets all the requirements of a modern surface paver: It is user-friendly, offers precise installation technology, and impresses with its maneuverability – even on confined construction sites, such as underground garages. Thanks to its lightweight aluminum construction and compact dimensions, the machine can be easily transported to any construction site.
The flexibility of the Paving Machine is further enhanced by the ability to load it from three sides using a wheel loader. The low-vibration track drive ensures smooth operation, while modern joysticks enable precise machine control. The paver is suitable for surfaces ranging from approximately 300 m² to 10,000 m² and more – with a daily output that can be achieved by an experienced operator.
The screed is controlled by two independent systems. For example, the ultrasonic sensor can be operated in parallel with the laser or cross-slope sensor. Sensor switching occurs seamlessly when transitioning from ultrasound to another sensor (e.g., for oscillating gutters). Our laser receivers, which are permanently and precisely calibrated on the screed, guarantee accurate height measurement, significantly simplifying height control.
Automation features such as automatic bunker flaps, screed intake cylinders, and the material distributor further enhance user-friendliness and simplify machine handling.
The radio remote control offers clear advantages: It enables more precise control of the undercarriage to achieve exact edge installation. Additionally, the compact and user-friendly operation provides greater comfort. In poor visibility or high dust conditions, the machine can be safely and efficiently controlled from the outside – ensuring greater control, flexibility, and safety on the construction site.
A specially designed bunker flap construction ensures uniform and precise dosing of bulk material across the entire screed width.
Our first patent, the oscillating screed, ensures that the machine’s inclination does not affect the screed, allowing for an even layer thickness during installation. With our second patent, we can integrate a roof profile into the screed to create paths with a roof profile – a unique feature that makes the surface paver particularly attractive for urban applications, municipalities, and communities, such as in parks and pathway construction.
With simple modifications and the optionally available material distributors, the machine can also be used for paths with widths ranging from 2.05 m to 3.00 m (available at an additional cost).
The protection and safety of the operator are our top priorities. A visibility and stone guard is mounted at the operator's station on the front of the machine to ensure a safe working environment.
Custom special equipment for every construction site situation.
Customize your surface paver to meet your specific needs.
The material pusher ensures that the material is evenly moved from the center to the outside, achieving a maximum paving width of 3 m with a layer thickness of 10-15 cm. With automatic function.
Protective film on the front side - Note: Only available in combination with the operator’s protective roof. The tarp protects against dust and stone impact for the operator.
Rear weather protection, closing off to the screed, mesh banner (Logo HEIDE flaechenfertiger ® GmbH) for protection against wind and rain. (Extra charge applies for custom logos.)
MOBA-matic machine control. Required only in combination with the ultrasonic sensor.
Adjustable for one side only. 1 piece – either left or right. A total of 2 pieces is needed for a full machine setup. Only compatible with the controllers.
Precise "Moba" laser receiver for the HEIDE PRM-275 Surface Paving Machine.
Heide-HL2 rotary laser set for machine control and professional use with 1000 RPM and a calibrated telescope sight for quick axis detection (AutoSlope) with handheld receiver.
TELEMAT telescopic meter, extendable from 1,150 mm to 4,000 mm for precise measurements.
Sturdy aluminum crank tripod in a robust design with additional side supports.
MOBA-matic I machine control. Required only in combination with the ultrasonic or laser sensor. A total of 2 pieces is needed for a full machine setup.
MOBA-matic II machine control. Required only in combination with the ultrasonic or laser sensor. (Color display and digital switching between laser/ultrasonic and cross-slope sensor). A total of 2 pieces is needed for a full machine setup.
If the machine is to be equipped with a 3D machine control system (e.g., Leica, Moba, or other manufacturers upon request), the following components must be purchased directly from a dealer:
- Total station for construction, consisting of a total station, controller including software, prism pole, and prism
- Machine-side control, consisting of a machine control unit including 3D software, docking station, modem, and prism
Creation of custom company layouts (advertising) on foil, including application to the Surface Paving Machine.
727 spectrum 1 G II with two mounting brackets and carrying strap.
For manual cleaning, filter size SMF-MR1.8 for engines up to approx. 40 kW. Includes filter insert, quick-release clamp, two differential pressure gauges, warning device, and mounting brackets.
Initial filling with Motorex Ecosynt HEES 32 (approx. 30 l). Approved for work in water protection areas.
Training contents:
Practical and theoretical short training in the areas of: 1. Ultrasonic and laser control 2. Introduction to the rotary laser 3. Technical application on the HEIDE PRM-275 Surface Paving Machine 4. Construction site application. Additional travel and accommodation costs apply.
Training duration: 4 - 6 weeks. We train you in the following specialist areas:
01.1 Practical and theoretical application in laser and ultrasonic technology
01.2 Measurement and control applications on-site
01.3 Construction site management and customer interaction
01.4 Procedure for performance acceptance with the customer
01.5 Machine maintenance and servicing
01.6 Rotary laser introduction, calibration training, and practical exercises for laser setup, axis detection, and application on surfaces
01.7 You will receive a starter package containing all necessary documents for invoicing and offer creation, including general terms and conditions.
Benefit from over 17 years of professional experience with an annual total surface performance exceeding 400,000 square meters and more than 220 daily assignments per year. During your training, you will also have the opportunity to accompany me on job sites. The practical and theoretical training takes place directly on-site. After completing the training, you will have extensive knowledge with solid fundamental skills, enabling you to work smoothly and confidently from day one.
